How Do You Fix A Window Regulator Cable

September 02, 2021 Post a Comment

The hard part was getting the window. Hold the motor tightly against the regulator until you are ready to remove it there is a spool under the motor that will unwind quickly if you just pull on the motor.

Repair Manual Window Regulator 8 Steps Instructables

Sometimes rivets must even be drilled out to remove an old window regulator assembly.

How do you fix a window regulator cable. I finally got around to opening up the door panel to install my hopefully permanent fix for the problem of too much slack in the window regulator cable. It should go from the motor to the topbottom of the regulator channel when fixed to the door allowing a little leeway. Fold both sides of the regulator in and then remove it from the door.

When replacing a power window motor on a newer cable style regulator you should NOT let the cable wheel get out of the transmission housing. First inner door panels must be removed along with any weather barrier layers behind them. Slacken the adjustable pulley.

Undo the fixing screws to remove the regulator and cable drum and the cable. With the window held in place by the upper window frame you can now remove the window regulator from the door. As always uncut unedited first pers.

If this is ok remove the 3 bolts holding the motor onto the regulator. The hard part was getting the window out. I had mine do the same thing about a month ago.

Look at the cables on the regulator they tend to shred and ball up in the pulleys. Wiggle the motor until the wiring comes loose. Reverse the procedure to install the new regulator.

The window would still roll up and down properly it just wouldnt drop enough to clear the top. The cable along can not be repair the window regulator will have to be replace the regulator also comes with the window motor your window motor more then likely is good but thats the way they sell the regulator save the motor cause if yours ever goes bad you can just replace the window motor auto parts have this part runs about 10000. You will be replacing the whole.

Accessing window regulators typically requires a bit of labor. Start by removing the window-to-regulator bolts have someone hold the glass while you do this. Remove the regulator and disassemble.

After removing the door panel remove the window regulator. Make sure the cable does not come off of the spool during this process. Turn the ignition key to the on or accessory position.

Screw the new regulator and its loop of cable in position. When I sent mine off they repaired the plastic and replaced the. Then the window regulator can be accessed through cutouts on the interior door frame.

Press and hold the window switch in the closed or up position. Hit the bolts out pull out the tangled mess of cable please note the orientation of the spool with the marker before lifting it up from the disc If the disc is highly polished it may be better to scratch then mark the scratch. Disconnect the power motor from the regulator by unscrewing the bolts.

We are all human. Connect the leads of the voltmeter to the two terminals. The window had excessive play in the cable system which could be felt by rolling the window.

There are a couple places that can fix it you will have to take the window out and the regulator to send it off to be repaired unless there is a local repair company. Turn the key to the on position and move the window switch both up and down. Power Window Repair was founded on the premise that modern cable power window regulators were not only designed to break but break often.

The plastic where they hook into has broken and let one slip out. Make sure you buy the correct one. The sympton of my problem was that the window would not drop enough to clear the top when I opened the passenger side door.

To fit a new cable take the cable clamps off the bottom of the window glass push the window closed and tape it to the top of the frame. If the window switch is working correctly then the voltage reading will change showing a problem with the power window motor or power window regulator. Next remove the regulator bolts or rivets drill them out and snake the old regulator out through one of the door panel openings.

Bolt the regulator in place and then reinstall the motor and. The founder of Power Window Repair used his knowledge and experience in the engineering and automotive sector to design a way to re-manufacture and strengthen the OEM regulator making it stronger work like new and at a price that. Untangle the mess of cable.

With the window button depressed open and then slam the car door. Then remove the glass by tilting it away from the door and lifting it out. Loop it around the wheel twice Else the cable will be too short.

In this episode I repair my broken regulator cable simply by replacing it. First we attach the inner cable to the wheel and fix the wheel on the motor.

How To Replace A Car Window Motor Window Regulator Assembly Yourmechanic Advice